Interfejs do sterowania z kierownicy radiami Pionner/Sony/ JVC/ Alpine / Clarion/ Kenwood i inne w samchodach Peugeot oraz Citroen 42xpg013
Keep the original steering wheel remote control functions when replacing the factory radio with a retrofit HU. Depending on the vehicle equipment as well as the range of functions and software of the retrofit HU, individual operating functions may be omitted or replaced by other functions. Compare the pictured harness connectors with the connectors in your car and make sure that they fit optically and technically. Check if one of the listed OEM head units were installed originally. Also check vehicle functionality, vehicle settings and SWC functionality before final assembly. CAN Bus connector: 40 Pin Quadlock Citroen / Peugeot connector: OEM SWC > 3,5mm Jack / loose wire connector: OEM AUX > RCA(m) red / white connector: RCA(m) yellow not connected vehicles with Blaupunkt / Continental / Siemens VDO RD4 OEM HU with volume control knob vehicles with Clarion MQ-RD6 OEM HU monochrome display and central rotary knob vehicles with PDC rear vehicles without Bosch OEM HU vehicles without Continental RD45 OEM HU with volume control knob vehicles without Magneti Marelli RT3 / RT6 / Harman Becker OEM Sat Nav vehicles without JBL OEM amplified system vehicles without OEM rear speakers: PDC chimes to rear speaker output change connection front/rear speaker of the ISO plug vehicles Peugeot CC: SWC Citroen/Fiat/Peugeot/Toyota vehicles Quadlock PDC > item: 42a-1041-008 vehicles with Continental RD45 OEM HU with volume control knob: SWC Citroen/Fiat/Peugeot/Toyota vehicles Quadlock PDC > item: 42a-1041-008 vehicles with PDC switch: PDC chimes funktion must be activated vehicles with ECO-mode: connect +12V continuous current clamp 30 to batterie fused vehicle settings supported (look into the manual) dip switch settings for the retrofit device manufacturer (look into the manual) Vehicle application: Citroën Citroën Berlingo (7) 06/2008 - 03/2012 Citroën Berlingo (7) 04/2012 - 05/2015 Citroën Berlingo (7) 06/2015 - 06/2018 Citroën C2 (J) 12/2004 - 12/2009 Citroën C3 (F) 10/2005 - 01/2010 Citroën C3 (S) 01/2010 - 01/2017 Citroën C4 (L) 11/2004 - 08/2010 Citroën C5 (D) 10/2004 - 04/2008 Citroën C8 (E) 01/2008 - 07/2012 Citroën C8 (E) 07/2012 - 06/2014 Citroën DS3 (S) 03/2010 - 07/2014 Citroen Jumpy (V) 02/2007 - 05/2016 Citroen Jumpy (V) 09/2016 - 01/2024* Citroen Spacetourer (V) 03/2016 - 03/2024* Fiat Fiat Scudo (ZAF 270) 02/2007 - 07/2016 Opel Opel Vivaro C (V) 09/2019 - 01/2024* Opel Zafira Life V (V) 02/2019 - 01/2024* Peugeot Peugeot 207 (WC) 06/2006 - 06/2009 Peugeot 207 (W) 06/2009 - 07/2015 Peugeot 208 (C) 04/2012 - 04/2015 Peugeot 307 (3/3 Break/3 SW/3 CC) 06/2005 - 03/2009 Peugeot 308 (4/4 GTI/4 SW/4 CC) 09/2007 - 07/2015 Peugeot 407 (6/6 SW/6 Coupé) 05/2004 - 07/2008 Peugeot 407 (6/6 SW/6 Coupé) 02/2006 - 03/2011 Peugeot 607 (9) 10/2004 - 04/2009 Peugeot 807 (E) 07/2002 - 02/2008 Peugeot 807 (E) 02/2008 - 06/2014 Peugeot 3008 (OU) 06/2009 - 10/2013 Peugeot 5008 (O) 10/2009 - 10/2013 Peugeot Bipper (A) 12/2007 - 12/2015 Peugeot Expert (X) 02/2007 - 08/2016 Peugeot Expert (X) 03/2016 - 04/2024** Peugeot Partner (7) 05/2008 - 03/2012 Peugeot RCZ (4J) 04/2010 - 09/2015 Peugeot Traveller (V) 03/2016 -04/2024** Following signals are provided: Reimported vehicles or vehicles with different software may be incompatible in functions. red: +12V ignition clamp 15 orange: +12V illumination clamp 58 purple/white: +12V reverse gear signal pink: speed pulse signal green: GND park brake signal load capacity outputs: 250 mA max. current requirement more than 250 mA: 1 relay coil resistance 75 Ohm min. 2 relays coil resistance 150 Ohm min. SWC PDC rear supported vehicle settings supported *vehicles with PDC and Clarion MQ-RD6 OEM HU monochrome display and central rotary knob **vehicle settings not supported General installation instructions: Verification: 1: Check all operating functions and vehicle setting functions of the OEM HU. 2: Disconnect the OEM HU voltage-free. 3: Check all interface connections for correctness in a voltage-free. Connection and connection sequence: 1: Check settings and hardware configuration of the interface voltage-free. 2: Check configuration of the radio connection cable voltage-free. 3: Connect the radio connection cable according to the operating instructions of the retrofit HU. 4: Connect all other connections according to the operating instructions of the retrofit HU. 5: Connect the entire installation to the vehicle with the main connection last. 6: Software configuration of the interface according to the instructions in the item text and in the manual. 7: Configure the retrofit device according to the operating instructions of the retrofit device steering wheel remote control/camera/FSE/antenna phantom powering and others. 8: Function test of steering wheel remote control and vehicle Changes to the configuration of the interface and the radio connection cable: 1: Change configuration voltage-free 2: Reonnection see above 5 to 8 In case of malfunction of the interface or the vehicle: 1: Reinstall the OEM HU 2: Operate the OEM HU 3: Establish CAN bus shut down 4: Check the hardware configuration of the interface 5: Reconnection after CAN Bus shut down see above 5 and 6 More connections, connection changes, alternative connections, connections of loose cables or connection extensions of loose cables specified in the information text or the manual are for orientation purposes only and for the information of trained specialist instaler. More connections, changes to the cable configuration of the wiring harness or use of alternative connections or connection extensions: 1: Connections and changes are to be carried out exclusively by trained specialist installer. 2: Connections and modifications must be checked before connection for any manufacturer approvals or manufacturer warranty conditions that may be affected by the modifications. 3: Connections and modifications must be checked for function and correctness by measuring and comparing them with the vehicle's cable assignment diagram before connection. 4: Connections and modifications are made on the user's own responsibility without guarantee of function. 5: Connections and modifications are made on the user's own responsibility without any guarantee of damage to the vehicle, the retrofit device or the interface. 6: Modifications to the pre-assembled wiring harness may invalidate the product's warranty.